Cutting speeds: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
|||
Line 46: | Line 46: | ||
| single-flute || 3.175 || 500 || 0.75 || 80 || 10,000 || none || Works out fine, more speed should be possible. | | single-flute || 3.175 || 500 || 0.75 || 80 || 10,000 || none || Works out fine, more speed should be possible. | ||
|- | |- | ||
| single-flute || 3.175 || | | single-flute || 3.175 || 555 || 1.00 || 127 || 10,000 || none || Works out fine, more speed or attack should be possible. | ||
|- | |||
| single-flute || 3.175 || 555 || 2.00 || 127 || 10,000 || none || Works out fine, more speed or attack should be possible. | |||
|- | |- | ||
|} | |} | ||
== Examples === | |||
=== 12mm OSB, 3.175 single flute === | |||
[[GCode]] created with [[LaserWeb4]]. | |||
* Left | |||
** Cutting speed: 555mm/min | |||
** Attack: 1.00mm | |||
* Left | |||
** Cutting speed: 555mm/min | |||
** Attack: 2.00mm | |||
= Footer = | = Footer = |
Revision as of 16:41, 24 March 2024
🚧 | This is very much likely to change - I'm still learning every day! |
I used a 500W china spindle for my tests.
Plexiglas (PMMA)
Melts at 160°C (even earlier than your printer's PLA or PETG).
These are the main challenges:
- Make sure the chips leave the flute so they can't friction weld (dust shoe, compressed air)
- Finding the highest cutting volume (diameter*speed*attack) while keeping the tool as cool as possible
cutter | diameter (mm) | speed (mm/min) | attack (mm) | plunge (mm/min) | rpm | cooling | notes |
---|---|---|---|---|---|---|---|
single-flute | 2.0 | 300 | 30 | 0.5 | 10,000 | none | Great result, more should be doable! |
single-flute | 2.0 | 400 | 30 | 0.75 | 10,000 | none | Looks good, might be the limit before it shows. |
Engraving
0.5mm deep TBD TBD
Poplar plywood (Pappelsperrholz)
cutter | diameter (mm) | speed (mm/min) | attack (mm) | plunge (mm/min) | rpm | cooling | notes |
---|---|---|---|---|---|---|---|
single-flute | 2.0 | 300 | 30 | 2.0 | 10,000 | none | Great result, more should be doable! |
Pine plywood (Kiefersperrholz)
cutter | diameter (mm) | speed (mm/min) | attack (mm) | plunge (mm/min) | rpm | cooling | notes |
---|---|---|---|---|---|---|---|
single-flute | 2.0 | 400 | 2.0 | 100 | 10,000 | none | Works out fine, more speed should be possible. |
OSB (Grobspanplatten)
cutter | diameter (mm) | speed (mm/min) | attack (mm) | plunge (mm/min) | rpm | cooling | notes |
---|---|---|---|---|---|---|---|
single-flute | 3.175 | 500 | 0.75 | 80 | 10,000 | none | Works out fine, more speed should be possible. |
single-flute | 3.175 | 555 | 1.00 | 127 | 10,000 | none | Works out fine, more speed or attack should be possible. |
single-flute | 3.175 | 555 | 2.00 | 127 | 10,000 | none | Works out fine, more speed or attack should be possible. |
Examples =
12mm OSB, 3.175 single flute
- Left
- Cutting speed: 555mm/min
- Attack: 1.00mm
- Left
- Cutting speed: 555mm/min
- Attack: 2.00mm
- Links
- TBD