Raspberry Pi as Standalone Access Point: Difference between revisions
Line 15: | Line 15: | ||
net.ipv6.conf.all.disable_ipv6=1 | net.ipv6.conf.all.disable_ipv6=1 | ||
Explanation: Disable [[IPv6]] (to [[KISS]]). | Explanation: Disable [[IPv6]] (to [[KISS]]). | ||
== Disable DHCP-Client == | |||
vi /etc/dhcpcd.conf | |||
and set something like this: | |||
nohook wpa_supplicant ???? | |||
denyinterfaces wlan0 ???? | |||
Explanation: I omit <tt>/etc/wpa_supplicant/wpa_supplicant.conf</tt> for <tt>wlan0</tt>. It is essential that there remains only one layer3-active (meaning using IP) interface, and that is <tt>br0</tt>. Otherwise you get a routing mess. | |||
Since <tt>br0</tt> and <tt>eth0</tt> are not omitted (denied), they get [[IPA]]s from the [[DHCP]]-Server. That's necessary for <tt>br0</tt>, and not for <tt>eth0</tt> (but when I omitted <tt>eth0</tt>, the bridge didn't come up. So I removed the [[IPA]] later (see below). | |||
== Set Static IP-Address == | == Set Static IP-Address == |
Revision as of 17:58, 28 November 2020
WIP - WIP - WIP
I had a case (that has yet to be documented here), where I needed an Raspberry Pi Zero WH to act as access point, including DHCP-Server. Standalone, not connected to any network.
Installation
apt-get install hostapd dnsutils traceroute isc-dhcp-server
Configuration
Disable IPv6
vi /etc/sysctl.conf
and set
net.ipv6.conf.all.disable_ipv6=1
Explanation: Disable IPv6 (to KISS).
Disable DHCP-Client
vi /etc/dhcpcd.conf
and set something like this:
nohook wpa_supplicant ???? denyinterfaces wlan0 ????
Explanation: I omit /etc/wpa_supplicant/wpa_supplicant.conf for wlan0. It is essential that there remains only one layer3-active (meaning using IP) interface, and that is br0. Otherwise you get a routing mess. Since br0 and eth0 are not omitted (denied), they get IPAs from the DHCP-Server. That's necessary for br0, and not for eth0 (but when I omitted eth0, the bridge didn't come up. So I removed the IPA later (see below).
Set Static IP-Address
Enable and Configure Access Point
vi /etc/default/hostapd
and set:
DAEMON_CONF="/etc/hostapd/hostapd.conf"
Explanation: The hostapd reads the configfile, to find this configfile. I don't get what this is good for. I think I'm just net getting the whole concept. If anyone cares to enlighten me, please do. :)
vi /etc/hostapd/hostapd.conf
and set something like this:
interface=wlan0 driver=nl80211 hw_mode=g channel=7 ieee80211n=1 wmm_enabled=1 macaddr_acl=0 auth_algs=1 ignore_broadcast_ssid=0 wpa=2 wpa_key_mgmt=WPA-PSK wpa_pairwise=TKIP rsn_pairwise=CCMP ssid=HMS_Camden_Lock wpa_passphrase=42_42_42_42
Explanation: hostapd creates the WiFi-Access Point and creates a bridge-device br0, which he ties (only) wlan0 to[1].
Enable and Configure DHCPd
vi /etc/dhcp/dhcpd.conf
…set…
default-lease-time 600; max-lease-time 7200;
…un-comment this:
authoritative;
…set your ip range:
subnet 10.178.42.0 netmask 255.255.255.0 { range 10.178.42.100 10.178.42.240;
- option routers 10.178.somebyte.anotherbyte;
option domain-name "pi00.wurst-wasser.net"; option domain-name-servers 127.0.0.1; }
Launch it:
systemctl start isc-dhcp-server.service
Setup DNS
Later. Not mattering right now.
Network Interfaces
vi /etc/network/interfaces
Don't touch this file. dhcpcd gets jealous...
- Links
- Footnotes
- ↑ Check with: brctl show